Protect Elast FS 2K (CER 055 T 2K)

Cement and polymer dispersion based elastic waterproofing product

Technical Specifications

Color	Gray
Density	1.4 kg(±0.05)/l
Packaging	20 kg Bag (A) and 10 kg Plastic Drum (B)
Shelf Life(25°C 55%RH)	12 Months (Unopened)
Pot Life	2 Hours
Setting Time	6 Hours
Average Consumption	1.9 kg/m² ( for 2 mm coat thickness)
Component A	Special cement with mineral fillers and polymer
Component B	Liquid Polymer Dispersion
Full Cure Time	After 3 Days (Mechaincal Resistance) After 5 Days (Water Resistance) After 7 Days (Fully Cured)

Description

PROTECT-A CER 055 T 2K is a cement and polymer dispersion based, elastic waterproofing material.

Area of Use

Suitable for indoor and outdoor use.
Suitable for horizontal and vertical applications.
In swimming pools and thermal pools (with ceramic coating).
Wall and floor coverings of cold storage rooms.
In all wet areas of the building such as WC, bathroom, kitchen.
In foundation and retaining walls.

Product Features and Advantages

Plastic consistency provides ease of application.
A horizontal and vertical application gives excellent results thanks to its excellent adhesion and retention qualities.
Provides impermeability and durability against pressurized water.
Resistant to freezing and abrasion.

Application Instructions

Application surface should be clean, dry, smooth and free from dirt, dust, oil, wax, mildew, tar, old paint and any other bond breaking residues.
Surface defects with a depth of more than 1 cm should be restored at least 6-8 hours before the application.
Concrete and cement-based plaster surfaces should be moistened with clean water. Before starting the application, it is necessary to wait for the surface to absorb the water.
After the surface is cleaned and repaired, the surface should be primed with a single layer and should be left to dry for 1-3 hours in order to increase the adhesion strength between layers and balance the surface absorbency.
Powder is added to the liquid part in a clean container and mixed with a 400-600 rpm mixer for 3-5 minutes until a homogenous and lump-free mixture is obtained. After letting it rest for 3-5 minutes and mixing again for an additional 30 seconds, the material becomes ready for use. Product should be applied to the surface at least two or three times (depending on the surface) in order to obtain a dry film thickness of 2 mm. After the first coat is completely dry, the second and the following coatings should be done perpendicular to the previous applications.
Chamfering should be made with the repair mortar on the joints of edges and corners.
In cases where chamfering is not possible, tape should be applied in areas that are weak in terms of water impermeability, such as edge joints.
Depending on the feature of the application surface, application can also be done by placing a mesh between two layers when necessary. In cases that require mesh reinforcement, the mesh must be placed on the first coating before it dries.

Application Notes

During the coating process over insulation, care should be taken not to damage the insulation material with mechanical effects.
The product should be used within the pot life after mixing. Products that have reached the end of their pot life should never be used during application.
During the application, no foreign materials should be added into the mixture other than the components of the product.
It should not be applied on uneven surfaces.
The strength and bearing of old surfaces should be checked before application.
During and after the application, the surface should be protected from air currents and contact with water.
It should not be applied on substrates that are at risk of frost, frozen or that were in contact with melting ice within the past 24 hours.
Care should be taken not to expose the material to direct sunlight in hot weather.
Application should not be done on hot surfaces exposed to excessive winds or direct sunlight, if there is a necessity to apply in these environments, the environment and the surface should be prepared specifically for application before starting.
It should not be applied during rainy weather.
The applied surface should be protected from rain for 24 hours.
Surface and ambient temperature should be between +5°C and +35°C during application.

Protect A CER 055 T 2K Technical Data Sheet

1 file(s) 286.19 KB

Download

Leave us your info

Please fill in the form to request product samples or for your inquires and we will get back to you.